Diamond and CBN Blades


Diamond blades and CBN (Cubic Boron Nitride) cutting blades are the preferred blade type when delicate and precise sectioning is needed. Diamond and CBN blades also perform better than traditional abrasive blades when cutting certain materials, especially very hard materials.

Buehler carries many different CBN blades and diamond blades in various diameters and thicknesses for many materials and applications including general use, hard materials, ceramic and petrographic samples, plastics and polymers, steel, and many more. Refer to the Ordering chart below to find the ideal diamond blade or CBN blade for your material and end application.

Precise, Clean Cuts:

  • Diamond and CBN blades offer thin blades that remove small amounts of material and reduce the surface damage.
  • Ideal choice when a precise and delicate cut is required. 

Unique Blades for Specific Applications:

  • Depending on the material being cut, a different combination of abrasive size, concentration and bond strength is needed. Buehler has developed blades for specific applications to ensure a high quality result is achieved. The selection table on the "Ordering" tab provides a recommended blade by application.

Wide Diameter Range: 

  • Precise sectioning is typically done on smaller precision cutters, but can also be done on larger saws. With diamond and CBN blades ranging from 3" [76mm] to 18" [450mm], precise sectioning can be done on all Buehler saws.

No specifications to show at the moment.

Precision Sectioning Blades for IsoMet™ Cutters, 0.5in [12.7mm] Arbor (qty 1)
Recommended Use 3in[76mm] 4in[102mm] 5in[127mm] 6in[152mm] 7in[178mm] 8in[203mm] Dressing Stick
Use with Saws All All All 1000
IsoMet High Speed
1000
IsoMet High Speed
IsoMet High Speed Only  
IsoMet 30HC - Polymers Rubber, Soft Gummy Materials 11-4239
0.030in [0.76mm]
11-4241
0.03in [0.76mm]
11-4242
0.035in [0.9mm]
Blade should not be dressed
IsoMet 20HC - Aggressive Sectioning of Metals 11-4215
0.020in [0.5mm]
11-4237
0.025in [0.76mm]
11-4238
0.035in [0.9mm]
11-1190
11-2490
IsoMet 15HC - Metal Matrix Composite, PCBs, Bone, Ti, TSC 11-4243
0.006in [0.15mm]
11-4244
0.012in [0.3mm]
11-4245
0.015in [0.5mm]
11-4246
0.02in [0.5mm]
11-4247
0.025in [0.6mm]
11-4248
0.035in [0.9mm]
11-1190
11-2490
IsoMet 20LC - Hard tough Materials, Structural Ceramics 11-4225
0.02in [0.5mm]
11-4227
0.025in [0.6mm]
11-4228
0.035in [0.9mm]
11-1190
11-2490
IsoMet 15LC - Hard Brittle Materials, Glass, Al2O3, ZrO3, Concrete 11-4253
0.006in [0.15mm]
11-4254
0.012in [0.3mm]
11-4255
0.015in [0.4mm]
11-4276
0.02in [0.5mm]
11-4277
0.025in [0.6mm]
11-4279
0.045in [1.1mm]
11-1190
11-2490
IsoMet 10LC - Medium to Soft Ceramics, Glass Fiber Reinforced Composites 11-4283
0.006in [0.15mm]
11-4285
0.015in [0.4mm]
11-4287
0.02in [0.5mm]
11-4288
0.045in [1.1mm]
11-1290
IsoMet 5LC - Soft, Friable Ceramics, Composites with Fine Reinforcing, CaF2, MgF2, Carbon Composites 11-4293
0.006in [0.15mm]
11-4295
0.015in [0.4mm]
11-1290
IsoCut™ CBN LC - Fe, Co, Ni based alloys and super alloys 11-4263
0.006in [0.15mm]
11-4264
0.012in [0.3mm]
11-4265
0.015in [0.4mm]
11-4266
0.02in [0.5mm]
11-4267
0.025in [0.6mm]
11-4268
0.035in [0.9mm]
11-1190
11-2490
IsoCut CBN HC - Fe, Co, Ni based alloys and super alloys 11-5264
0.012in [0.3mm]
11-5265
0.015in [0.4mm]
11-5266
0.02in [0.5mm]
11-5267
0.025in [0.6mm]
11-5268
0.035in [0.9mm]
11-1190
11-2490
Diamond & CBN Blades for Abrasive Cutters
[Blade Thickness is listed under Part Number] 1.25in 32[mm] Arbor (Qty 1)
Recommended use Blade Type 8in
[200mm]
10in
[250mm]
12in
[300mm]
14in
[350mm]
16in
[400mm]
General use Diamond 114608E
0.047in [1.2mm]
114610E
0.051in [1.3mm]
Hard materials Diamond 114808E
0.047in [1.2mm]
114810E
0.047in [1.2mm]
103056
0.055in [1.4mm]
114814E
0.059in [1.5mm]
104056
0.079in [2mm]
Ceramic and Petrographic samples Diamond 114709E*
0.047in [1.2mm]
114710E
0.047in [1.2mm]
103053
0.087in [2.2mm]
114714E
0.059in [1.5mm]
Plastics and Polymers Diamond 102557
0.049in [1.25mm]
General use, hardened steel, HRC55 and up CBN 103551
0.079in [2mm]


Diamond and CBN Blades
Sorry no videos at the moment.